Contact
Tel:+86 13015583380
Sales hot line ( 24 hours service):+86 13015583380
Sales hot line ( 24 hours service):+86 13015583380
E-Mail: firstfurnace@gmail.com
whatsapp:+86 13015583380
Adress: Luoxin Industrial Park, Luoyang, HenanLarge diameter steel pipe quen
Piston rod quenching and tempe
Grinding rod quenching and tem
High frequency induction heate
Quenching equipment for machin
Round steel end heating furnac
Steel pipe heat treatment prod
Square steel quenching and tem
Sucker rod quenching and tempe
Thickened petroleum steel pipe
Round steel quenching and temp
Steel pipe quenching and tempe
Steel plate quenching and temp
Induction Hardening Machine&nb
Flywheel ring gear high freque
Electric furnace repair（维修）
Preparation of the induction melting furnace before the furnace is opened
1. Whether the water gauge pressure indication is normal to determine the cooling water pressure;
2. Check the cooling water tank and whether the pipeline is blocked.
3. Check if the cooling water pipe joints of the thyristor, capacitor, filter reactor and water-cooled cable are corroded or leaking;
4. Check if the inlet water temperature meets the requirements;
5) Whether there are any attachments (such as conductive dust, residual iron, etc.) on the outer surface, gate and bottom of the induction coil. If compressed air is applied,
6. Whether the surface insulation of the induction coil is damaged, if any, use TSC-L ultra-high temperature insulation paint for partial repair. Avoid the formation of sparks or arcing to further damage the coil or power supply;
7. There is no crack at the junction of the fireplace lining and the taphole in the furnace lining. If the crack is more than 3mm, the lining material should be filled, and the bottom and the slag line should be partially eroded or thinned.
8. Check whether the copper wire and wire joints of the main circuit have heat and discoloration caused by poor contact, and if necessary, tighten the screws;
9. Check whether the instrument indication on the control panel of the control panel is normal;
10. Check if the leaking alarm device is normal and indicate whether the current is within the determined value;
11. Test the oil pump to check whether the hydraulic system oil level, pressure, leakage, tilting furnace and furnace lid cylinder are stable, normal and flexible;
12. Whether there is any debris (magnetic substance) in the bottom of the furnace, it will heat up if it is not removed;
1. Whether the water gauge pressure indication is normal to determine the cooling water pressure;
2. Check the cooling water tank and whether the pipeline is blocked.
3. Check if the cooling water pipe joints of the thyristor, capacitor, filter reactor and water-cooled cable are corroded or leaking;
4. Check if the inlet water temperature meets the requirements;
5) Whether there are any attachments (such as conductive dust, residual iron, etc.) on the outer surface, gate and bottom of the induction coil. If compressed air is applied,
6. Whether the surface insulation of the induction coil is damaged, if any, use TSC-L ultra-high temperature insulation paint for partial repair. Avoid the formation of sparks or arcing to further damage the coil or power supply;
7. There is no crack at the junction of the fireplace lining and the taphole in the furnace lining. If the crack is more than 3mm, the lining material should be filled, and the bottom and the slag line should be partially eroded or thinned.
8. Check whether the copper wire and wire joints of the main circuit have heat and discoloration caused by poor contact, and if necessary, tighten the screws;
9. Check whether the instrument indication on the control panel of the control panel is normal;
10. Check if the leaking alarm device is normal and indicate whether the current is within the determined value;
11. Test the oil pump to check whether the hydraulic system oil level, pressure, leakage, tilting furnace and furnace lid cylinder are stable, normal and flexible;
12. Whether there is any debris (magnetic substance) in the bottom of the furnace, it will heat up if it is not removed;
13. Whether there is water or moisture in the iron pit, if it should be eliminated and dried.
Be sure to pay attention to safety when using the induction melting furnace
Iron induction furnace
Aluminum melting furnace
Copper melting furnace
Small steel melting furnace
Small induction melting furnace
Induction iron furnace
3T intermediate frequency iron melting f
0.25T Intermediate Frequency Furnace
0.5T Intermediate Frequency Furnace
Medium Frequency Furnace
2T Induction Melting Furnace
1T Induction Melting Furnace
500kg Induction Melting Furnace
250kg Induction Melting Furnace
Induction Melting Furnace
3 T Induction Melting Furnace
5T Induction Melting Furnace
1T One Belt Two Intermediate Frequency F
5T One Belt Two Intermediate Frequency F
3T One Belt Two Intermediate Frequency F
2T One Belt Two Intermediate Frequency F
5T Parallel Intermediate Frequency Furna
5T Intermediate Frequency Furnace
5T Series Intermediate Frequency Furnace
3T Series Intermediate Frequency Furnace
2T Series Intermediate Frequency Furnace
1T Series Intermediate Frequency Furnace
0.5T Series Intermediate Frequency Furna
0.25T Series Intermediate Frequency Furn
1T Parallel Intermediate Frequency Furna
2T Parallel Intermediate Frequency Furna
0.5T Parallel Intermediate Frequency Fur
Product Class