Contact
Tel:+86 13015583380
Sales hot line ( 24 hours service):+86 13015583380
Sales hot line ( 24 hours service):+86 13015583380
E-Mail: firstfurnace@gmail.com
whatsapp:+86 13015583380
Adress: Luoxin Industrial Park, Luoyang, HenanLarge diameter steel pipe quen
Piston rod quenching and tempe
Grinding rod quenching and tem
High frequency induction heate
Quenching equipment for machin
Round steel end heating furnac
Steel pipe heat treatment prod
Square steel quenching and tem
Sucker rod quenching and tempe
Thickened petroleum steel pipe
Round steel quenching and temp
Steel pipe quenching and tempe
Steel plate quenching and temp
Induction Hardening Machine&nb
Flywheel ring gear high freque
Electric furnace principle（原理）
Thyristor medium frequency electric furnace shock treatment method
Intermediate frequency furnace maintenance: thyristor medium frequency electric furnace shock treatment method 1: The intermediate frequency furnace can not be started, only the DC current meter has indication when starting, and the DC voltage and intermediate frequency voltmeter have no indication.
The capacitor is broken down and the damaged capacitor pole is removed.
The load has a short circuit, grounding phenomenon, and the short circuit point and grounding point are eliminated.
The IF signal sampling loop has an open or short circuit phenomenon. Use an oscilloscope to observe the waveform of each signal sampling point and find the open or short circuit point.
Medium frequency furnace maintenance: thyristor medium frequency electric furnace shock treatment method 2: When the heavy load cold furnace starts, the electrical parameters and sounds are normal but the power is not up to overcurrent protection.
Analysis and processing:
The inverse transform flow angle is too small. Use an oscilloscope to view the commutation angle of the inverter thyristor, and adjust the commutation angle to an appropriate value;
The insulation resistance of the furnace body is low or short-circuited, and the resistance value of the furnace body is detected by a megger to eliminate the short-circuit point of the furnace body;
The resistance of the furnace steel relative to the induction coil is low, and the resistance of the furnace relative to the induction coil is detected by a megohmmeter; if the resistance is low, the furnace is rebuilt.
The furnace switch has a grounding phenomenon or the switch contacts have poor contact, and the furnace switch or contact is replaced.
Medium frequency furnace maintenance: thyristor medium frequency electric furnace shock treatment method 3: starting difficulty, the maximum DC voltage can only rise to 1400v after starting, and the reactor vibration is large, the sound is dull.
Rectifier thyristor open circuit, breakdown, soft breakdown or electrical parameter performance degradation, use an oscilloscope to observe the voltage drop waveform of each rectifier thyristor, find the damaged thyristor and replace it.
A set of rectification trigger pulses is missing. Each oscilloscope is used to check each trigger pulse. When a loop without a pulse is detected, the fault location is determined by the reverse push method, and the damaged device is replaced.
Intermediate frequency furnace maintenance: thyristor medium frequency electric furnace shock treatment method 1: The intermediate frequency furnace can not be started, only the DC current meter has indication when starting, and the DC voltage and intermediate frequency voltmeter have no indication.
Inverter trigger pulse phenomenon, use the oscilloscope to check the inverter pulse (check on the thyristor AK), if there is a lack of pulse phenomenon, check whether the connection is not well contacted or open circuit, whether there is pulse output in the front stage.
The capacitor is broken down and the damaged capacitor pole is removed.
The load has a short circuit, grounding phenomenon, and the short circuit point and grounding point are eliminated.
The IF signal sampling loop has an open or short circuit phenomenon. Use an oscilloscope to observe the waveform of each signal sampling point and find the open or short circuit point.
Medium frequency furnace maintenance: thyristor medium frequency electric furnace shock treatment method 2: When the heavy load cold furnace starts, the electrical parameters and sounds are normal but the power is not up to overcurrent protection.
Analysis and processing:
The inverse transform flow angle is too small. Use an oscilloscope to view the commutation angle of the inverter thyristor, and adjust the commutation angle to an appropriate value;
The insulation resistance of the furnace body is low or short-circuited, and the resistance value of the furnace body is detected by a megger to eliminate the short-circuit point of the furnace body;
The resistance of the furnace steel relative to the induction coil is low, and the resistance of the furnace relative to the induction coil is detected by a megohmmeter; if the resistance is low, the furnace is rebuilt.
The furnace switch has a grounding phenomenon or the switch contacts have poor contact, and the furnace switch or contact is replaced.
Medium frequency furnace maintenance: thyristor medium frequency electric furnace shock treatment method 3: starting difficulty, the maximum DC voltage can only rise to 1400v after starting, and the reactor vibration is large, the sound is dull.
Rectifier thyristor open circuit, breakdown, soft breakdown or electrical parameter performance degradation, use an oscilloscope to observe the voltage drop waveform of each rectifier thyristor, find the damaged thyristor and replace it.
A set of rectification trigger pulses is missing. Each oscilloscope is used to check each trigger pulse. When a loop without a pulse is detected, the fault location is determined by the reverse push method, and the damaged device is replaced.
Iron induction furnace
Aluminum melting furnace
Copper melting furnace
Small steel melting furnace
Small induction melting furnace
Induction iron furnace
3T intermediate frequency iron melting f
0.25T Intermediate Frequency Furnace
0.5T Intermediate Frequency Furnace
Medium Frequency Furnace
2T Induction Melting Furnace
1T Induction Melting Furnace
500kg Induction Melting Furnace
250kg Induction Melting Furnace
Induction Melting Furnace
3 T Induction Melting Furnace
5T Induction Melting Furnace
1T One Belt Two Intermediate Frequency F
5T One Belt Two Intermediate Frequency F
3T One Belt Two Intermediate Frequency F
2T One Belt Two Intermediate Frequency F
5T Parallel Intermediate Frequency Furna
5T Intermediate Frequency Furnace
5T Series Intermediate Frequency Furnace
3T Series Intermediate Frequency Furnace
2T Series Intermediate Frequency Furnace
1T Series Intermediate Frequency Furnace
0.5T Series Intermediate Frequency Furna
0.25T Series Intermediate Frequency Furn
1T Parallel Intermediate Frequency Furna
2T Parallel Intermediate Frequency Furna
0.5T Parallel Intermediate Frequency Fur
Product Class