Contact
Tel: 18037961302
Sales hot line ( 24 hours  service): 18037961302

E-Mail: firstfurnace@gmail.com

whatsapp:+8618037961302

Adress: Luoxin Industrial Park, Luoyang, Henan
  • Products
  • 0.25T Intermediate Frequency F

    0.5T Intermediate Frequency Fu

    Medium Frequency Furnace

    2T Induction Melting Furnace

    1T Induction Melting Furnace

    500kg Induction Melting Furnac

    250kg Induction Melting Furnac

    Induction Melting Furnace

    3 T Induction Melting Furnace

    5T Induction Melting Furnace

    1T One Belt Two Intermediate F

    5T One Belt Two Intermediate F

    3T One Belt Two Intermediate F

    2T One Belt Two Intermediate F

    5T Parallel Intermediate Frequ

    5T Intermediate Frequency Furn

    5T Series Intermediate Frequen

    3T Series Intermediate Frequen

    2T Series Intermediate Frequen

    1T Series Intermediate Frequen

    0.5T Series Intermediate Frequ

    0.25T Series Intermediate Freq

    1T Parallel Intermediate Frequ

    2T Parallel Intermediate Frequ

    0.5T Parallel Intermediate Fre

    0.25T Parallel Intermediate Fr

    Parallel Intermediate Frequenc

    3T Intermediate Frequency Furn

    Medium frequency copper melting furnace

    product description

        

    Uses: for melting copper powder, copper wire, copper scrap, copper block, copper, copper electrolytic copper melting furnace, copper was melted, the molten copper, the molten copper strip, the molten brass, the molten copper, the molten copper foil device,

    image.png 

    1, IF copper melting furnace equipment selection table

    KGPS

    copper

    Input voltage

    Melting timemin

    SD - 7kw

    2KG

    220v

    10min

    SD -15 kw

    10KG

    380v

    10min

    SD -25 kw

    20KG

    380v

    20min

    SD Z-35 kw

    40KG

    380v

    30min

    SD Z- 45kw

    60KG

    380v

    30min

    SD Z- 70kw

    100KG

    380v

    30min

    SD Z- 90kw

    120KG

    380v

    40min

    SD Z- 110kw

    150KG

    380v

    50min

    SD Z- 160kw

    200KG

    380v

    60min

    2 , medium frequency copper melting furnace configuration:

    Serial number

    name

    unit

    Quantity

    1

    Medium frequencypower supply(KGPS)

    station

    1

    2

    Capacitor compensation box

    station

    1

    3

    Electric overturningfurnace

    station

    1

    4

    Split connection cable

    One

    1

    5

    Output water cooled cable

    set

    1

    6

    control box

    One

    1

    3 , customer self- installed machine accessories ( circulation cooling system ) :

    1. Three-phase air switch 400A ;

    2. Power connection soft cable 90 mm2 several meters;

    3 . Cooling tower 30 tons 1;

    4. Pump 3.0kw/ head 30-50 meters set ;

    , equipment inlet and outlet water pipes: high pressure enhanced water pipe outer diameter 16 mm, inner diameter 12 mm several meters

    6. Water pump inlet and outlet water pipe: inch (inner diameter 25 mm) with wire high pressure reinforced pipe several meters

    4, IF copper melting furnaces steps:

    1, electrical connection: access to a dedicated power supply line, respectively, three-phase air switch. Then connect the ground wire. ( Note that the three-phase electric power should be able to meet the use of the equipment, and the wire thickness should be used according to the instructions )

    , water: (depending on continuous working time and workload) select the cooling water system to achieve water circulation cooling.

    , water: open the waterway, and check the water outlet of each device to see if there is water outflow, whether the flow and pressure are normal .

    4, power: the power switch to open the control, followed by a switch to open the air behind the machine, and then turn the power switch on the control panel.  

    , start: Before the first furnace starts, the heating power potentiometer should be adjusted to the minimum as much as possible, and then slowly adjusted to the required power after starting. Press the start button to start the machine. At this time, the heating indicator on the panel lights up, and the prompt sound of normal operation and the work light flash simultaneously. 
    6. Observation and temperature measurement: In the heating process, it is mainly determined by visual inspection when to stop heating.

    7. Shutdown: Shutdown, the control device switches off first, then turn off the main power external switch, then delayed until about hour after the furnace temperature down; then off equipment cooling water, the heat inside the machine to facilitate the induction loop and the heat distributing . 
    8. In areas where it is easy to freeze in winter , it should be noted that after each use, compressed air should be used to blow out the water in and out of the equipment to prevent internal cracking of internal fittings and water pipes.

    5 , customer molten copper scene picture:

    image.png


    Copyright© 2007-2013 songdao Electric furnace manufacturing Co,.Ltd All Rights Reserved
    Tel:18037961302 Sales hot line ( 24 hours service): 18037961302
    E-Mail:firstfurnace@gmail.com
    Adress: Luoxin Industrial Park, Luoyang, Henan