Contact
Tel: 18037961302
Sales hot line ( 24 hours  service): 18037961302

E-Mail: firstfurnace@gmail.com

whatsapp:+8618037961302

Adress: Luoxin Industrial Park, Luoyang, Henan
  • Products
  • Gear hardening machine

    Large diameter steel pipe quen

    Piston rod quenching and tempe

    Hand-held induction heater

    Grinding rod quenching and tem

    Induction forging machine

    induction heating machine 

    Induction heater

    High frequency induction heate

    Super audio induction heating

    Super audio induction heating

    Guideway quenching integrated

    Quenching equipment for machin

    Round steel end heating furnac

    Steel pipe heat treatment prod

    Square steel quenching and tem

    Sucker rod quenching and tempe

    Thickened petroleum steel pipe

    Round steel quenching and temp

    Steel pipe quenching and tempe

    Steel plate quenching and temp

    Induction Hardening Machine&nb

    Flywheel ring gear high freque

    Oil drill pipe quenching and t

    Iron induction furnace

    Aluminum melting furnace

    Copper melting furnace

    Small steel melting furnace

    Electric furnace technical information£¨¼¼Êõ£©
        

    Technical specifications for water-cooled cables for medium frequency furnaces The cross-section is in the range of 25 to 6000 square millimeters; the length is in the range of 0.3 to 70 meters, which conforms to the national standard GB.

    1. The electrode (also called the cable head) is non-contact, no solder joint, no weld seam, and is processed with a whole copper rod on a CNC lathe and milling machine. It is beautiful and durable; the connection between the electrode and the wire is cold. Squeeze, do not hurt the line, the resistance is small.

    Second, the outer casing, the use of hose, water pressure >0.8MPA, breakdown voltage is higher than 3000V. There is also a flame-retardant outer casing for users to choose in special occasions;

    Third, the electrode and the outer casing are fastened. The cable below 500mm2 is made of copper clamp. The other ones are made of 1Cr18Ni9Ti. It is non-magnetic and does not rust. It is squeezed and fastened with large hydraulic equipment. It is beautiful, durable and has good sealing effect.

    Fourth, the soft wire is processed by a fine enamel wire on a special winding machine. Soft, small bending radius, large effective section;

    5. The enameled wire is used as a water-cooled cable, and the power transmission efficiency is high. Because of the insulation between each enameled wire, the intermediate frequency, high-frequency current is transmitted, and there is no surface skin effect. Compared with other water-cooled cables of the same cross-section, the heat is less when passing the same current;

    6. Use the enameled wire to make the wire of the water-cooled cable, which can improve the service life of the water-cooled cable. Because the wire of the water-cooled cable is immersed in water for a long time, the working environment is very bad. In the past, we used copper bare wire as a water-cooled cable. When the water-cooled cable was used for a period of time, open the cable jacket and you will see a layer of green copper rust on the wire surface. Later, we switched to enameled wire to make water-cooled cable. Because the enameled wire has a protective layer of paint film, it can play a role in anti-corrosion. The user reports that the water-cooled cable made of enameled wire has a service life of 1.5 to 2 times that of bare copper wire.


    Copyright© 2007-2013 songdao Electric furnace manufacturing Co,.Ltd All Rights Reserved
    Tel:18037961302 Sales hot line ( 24 hours service): 18037961302
    E-Mail:firstfurnace@gmail.com
    Adress: Luoxin Industrial Park, Luoyang, Henan