Contact
Tel: 18037961302
Sales hot line ( 24 hours service): 18037961302
Sales hot line ( 24 hours service): 18037961302
E-Mail: firstfurnace@gmail.com
whatsapp:+8618037961302
Adress: Luoxin Industrial Park, Luoyang, HenanLarge diameter steel pipe quen
Piston rod quenching and tempe
Grinding rod quenching and tem
High frequency induction heate
Quenching equipment for machin
Round steel end heating furnac
Steel pipe heat treatment prod
Square steel quenching and tem
Sucker rod quenching and tempe
Thickened petroleum steel pipe
Round steel quenching and temp
Steel pipe quenching and tempe
Steel plate quenching and temp
Induction Hardening Machine&nb
Flywheel ring gear high freque
Industrial electric furnace technical information
1. The fast furnace saves electricity compared to the slow furnace. The same set of equipment is faster than slower power saving. The timing and tightness of the feeding and the size of the furnace will affect the melting speed. These points need to be the best at the same time, the power consumption is the least.
2, the need to take into account the current meter, try to make the power stable. Maximize the output power of the device as much as possible.
3. Precisely control the temperature of molten iron. Do not let the temperature be too high or too high. It is not good for electricity consumption and lining life. A good furnace can save electricity and be efficient.
4. Choose the right equipment. If the furnace is too large or too small, it may increase the power consumption. The same large furnace saves power, and the same fast intermediate frequency furnace saves electricity. The high voltage is lower than the low voltage. Casting time also affects power consumption, and it is best be controlled in 5-10 minutes.
5, do not need low-end equipment . The market is fiercely competitive,Some manufacturers cut corners and compete at low prices, and the worse the equipment materials are, the greater the loss. If the copper row is not plated directly and used with a relatively thin copper material, the device will start to look the same, but the power consumption will be higher and higher.
6, the line can not be saved, must be large enough, otherwise the long-term loss is quite amazing.
7, develop a good boot habit, power as much as possible and reduce the insulation or baking time. When the power is not full, the power factor is low and the loss is large.
8, improve the utilization of the transformer is also equal to power saving. A 630KVA transformer should be able to convert 13-15T tons of molten iron within 10 hours. If you can only produce 10-11 tons, your average electricity price must be higher than him.
9, scientific oven. When the medium frequency electric furnace is to be blown, the cooling water of the induction coil should be turned off (one third of the normal water volume), and the should be intermittently supplied with water to keep the water temperature above 55 degrees, so as to facilitate the smooth discharge of water vapor, which can shorten the drying. Furnace time. Some furnace workers did not pay attention to this point, and the water supply was normal. As a result, the water vapor discharged from the cold copper tube condensed into water, so that the oven was long and costly, and the effect was not good.
Reference power consumption:
Fused iron: 520-610 degrees / ton, 750-980 degrees / ton slow
Fused steel: fast 550-650 degrees / ton, slow 800-1000 degrees / ton
Copper melting: 310-360 degrees / ton, molten aluminum: 200-260 degrees / ton
Iron induction furnace
Aluminum melting furnace
Copper melting furnace
Small steel melting furnace
Small induction melting furnace
Induction iron furnace
3T intermediate frequency iron melting f
0.25T Intermediate Frequency Furnace
0.5T Intermediate Frequency Furnace
Medium Frequency Furnace
2T Induction Melting Furnace
1T Induction Melting Furnace
500kg Induction Melting Furnace
250kg Induction Melting Furnace
Induction Melting Furnace
3 T Induction Melting Furnace
5T Induction Melting Furnace
1T One Belt Two Intermediate Frequency F
5T One Belt Two Intermediate Frequency F
3T One Belt Two Intermediate Frequency F
2T One Belt Two Intermediate Frequency F
5T Parallel Intermediate Frequency Furna
5T Intermediate Frequency Furnace
5T Series Intermediate Frequency Furnace
3T Series Intermediate Frequency Furnace
2T Series Intermediate Frequency Furnace
1T Series Intermediate Frequency Furnace
0.5T Series Intermediate Frequency Furna
0.25T Series Intermediate Frequency Furn
1T Parallel Intermediate Frequency Furna
2T Parallel Intermediate Frequency Furna
0.5T Parallel Intermediate Frequency Fur
Product Class