Contact
Tel: 18037961302
Sales hot line ( 24 hours  service): 18037961302

E-Mail: firstfurnace@gmail.com

whatsapp:+8618037961302

Adress: Luoxin Industrial Park, Luoyang, Henan
  • Products
  • Gear hardening machine

    Large diameter steel pipe quen

    Piston rod quenching and tempe

    Hand-held induction heater

    Grinding rod quenching and tem

    Induction forging machine

    induction heating machine 

    Induction heater

    High frequency induction heate

    Super audio induction heating

    Super audio induction heating

    Guideway quenching integrated

    Quenching equipment for machin

    Round steel end heating furnac

    Steel pipe heat treatment prod

    Square steel quenching and tem

    Sucker rod quenching and tempe

    Thickened petroleum steel pipe

    Round steel quenching and temp

    Steel pipe quenching and tempe

    Steel plate quenching and temp

    Induction Hardening Machine&nb

    Flywheel ring gear high freque

    Oil drill pipe quenching and t

    Iron induction furnace

    Aluminum melting furnace

    Copper melting furnace

    Small steel melting furnace

    Electric furnace technical parameters(²ÎÊý£©
        

     Safety Notes Of Induction melting Furnace

    1. IGBT/KGPS Induction smelting furnace coil and water cooling cable in working are strictly prohibited to personnel contact. it is a normal phenomenon that water cooling pipe and cooling water have induced voltage, and also can not contact when working.

    2. The Induction melting furnace coil is electrified body, therefore, furnace building materials should not contain any conductive material, such as metal, graphite powder and the molten metal can¡¯t contact the induction coil, otherwise it will bring danger to the furnace operation workers.

    3. After Induction melting furnace table is built up, it must be placed rubber insulation adhesive and drying of wood. When working, the rubber insulation adhesive should be placed on drying of wood, the operation worker should stand on the wood, hand wear insulated gloves (welder gloves), foot wear insulated shoe to make sure the safety. In the process of melting, people can¡¯t stand around furnace to prevent the explosion accidents.

    4. Water cooling cable and water pipe can¡¯t be contacted with ground when working to keep it in good condition of insulation.


    5. IGBT/KGPS power supply and electric furnace no water leakage, once found  , it must cut power and repair.

    6. Furnace lining has certain service life. According to the life of furnace lining materials, even if not found lining defects, it also should be removed to prevent leakage phenomenon of furnace. If there is leakage of furnace, first close the IGBT /KGPS power supply immediately, evacuate the surrounding people, then pour out the liquid metal in the furnace body to prevent the metal liquid water explosion.

    7. Before starting up the Induction smelting furnace, must check whether the lining material has crack and other defects. Once found, it¡¯s not allowed to start up the machine, should be replaced lining material immediately.

    8. IBGT/KGPS power supply, pipe, furnace body and other electric equipment maintenance, should be confirmed that the power has already cut off.


    10. Frozen furnace in melting again, furnace body should be about 30 degrees forward. The molten metal around the induction coil should become melting before the full power operation.

    11. IGBT/KGPS power supply shell, capacitor box shell, furnace table, reducer, furnace feet all need to protect earth. Connecting with a diameter of 10mm iron bar, put the iron bar into the underground 3 meters deep and requires grounding resistance less than 10.

    12. Grounding protection requirements: meet the electricity sector grounding protection requirements.



    Copyright© 2007-2013 songdao Electric furnace manufacturing Co,.Ltd All Rights Reserved
    Tel:18037961302 Sales hot line ( 24 hours service): 18037961302
    E-Mail:firstfurnace@gmail.com
    Adress: Luoxin Industrial Park, Luoyang, Henan