Contact
Tel: 18037961302
Sales hot line ( 24 hours  service): 18037961302

E-Mail: firstfurnace@gmail.com

whatsapp:+8618037961302

Adress: Luoxin Industrial Park, Luoyang, Henan
  • Products
  • Gear hardening machine

    Large diameter steel pipe quen

    Piston rod quenching and tempe

    Hand-held induction heater

    Grinding rod quenching and tem

    Induction forging machine

    induction heating machine 

    Induction heater

    High frequency induction heate

    Super audio induction heating

    Super audio induction heating

    Guideway quenching integrated

    Quenching equipment for machin

    Round steel end heating furnac

    Steel pipe heat treatment prod

    Square steel quenching and tem

    Sucker rod quenching and tempe

    Thickened petroleum steel pipe

    Round steel quenching and temp

    Steel pipe quenching and tempe

    Steel plate quenching and temp

    Induction Hardening Machine&nb

    Flywheel ring gear high freque

    Oil drill pipe quenching and t

    Iron induction furnace

    Aluminum melting furnace

    Copper melting furnace

    Small steel melting furnace

    Electric furnace technical information£¨¼¼Êõ£©
        

    Manufacturing method of induction melting furnace coil

    1. Annealing in induction melting furnace. Before winding the induction coil, the rectangular pure copper tube is annealed. Keep the pure copper tube at 650~700¡æ for 30~40 minutes, and then quickly cool it in water at 20~30¡æ. Induction melting furnace for heating equipment.

    2. Induction melting furnace coil winding. Wind the rectangular pure copper tube into various profiling induction coils. Iron or wooden molds should be used when winding the coils of the induction melting furnace. Considering the springback of the rectangular copper tube after winding, the size of the mold should be slightly smaller than the required size. When the winding radius is small, heating winding should be performed, that is, acetylene flame is used to bake the pure copper tube at the bending part during winding.

    3. Induction melting furnace coil correction. Correct the wound induction coil to the required size and press it with a clamp.

    4. The annealing temperature, time and method after winding the induction coil of the induction melting furnace are the same as those of the pure copper tube.

    5. Induction melting furnace coil water pressure test. Pass water or air with a pressure 1.5 times the design pressure of the feedwater into the pure copper tube of the induction coil, and check whether there is water leakage at the joint between the pure copper tube and the pipe.

    6. The coil of the induction melting furnace is covered with an insulating layer. On the pure copper tube, 1/3 overlap and wrap the alkali-free glass ribbon.

    7. The coil of the induction melting furnace is impregnated with insulating paint. The induction coil covered with the insulating layer is preheated in an electric furnace or a hot air drying box, and then dipped in an organic insulating paint for 15 minutes. If there are many bubbles in the paint during the dipping process, the dipping time should be extended, generally three times.

    8. Induction melting furnace coil drying. It is carried out in an induction melting furnace or a hot air drying box. Induction melting furnace, when the induction coil is installed, the furnace temperature should not be higher than 50¡æ, and the temperature should be raised at a rate of 15¡æ/h, and it should be dried for 20h at 100~110¡æ, but it should be baked until the paint film does not stick to the hands.


    Copyright© 2007-2013 songdao Electric furnace manufacturing Co,.Ltd All Rights Reserved
    Tel:18037961302 Sales hot line ( 24 hours service): 18037961302
    E-Mail:firstfurnace@gmail.com
    Adress: Luoxin Industrial Park, Luoyang, Henan